No water at all
A tripped breaker, a failed pressure switch or control box, or a pump that has quit.
Check firstLook at the pump's breaker and the pressure gauge by the tank. Zero on the gauge points down the well.
Valdosta, GA · Pumps, tanks & switches
Well Pump Repair & Replacement in Valdosta, GA
When a well stops, the whole house stops with it. No shower, no flush, no water for the dishes. Most well pump repair in Valdosta starts with a short list of suspects, and the pump itself is the last of them, after the breaker, the pressure switch, the control box and the pressure tank. Call Plumber Valdosta Fix and you'll hear what to check, who should come out, and what it will cost before anyone pulls a pump. Pump running but no pressure? Switch its breaker off so it can't run dry, then call.
No water from the well? Call now and get a price first.
- 24/7No water in the house, any hour
- $0To call. You only pay for work you approve
- 10+Years helping homeowners get repairs done
10+Years helping homeowners get it fixed
- No water, any hourA dead well is a whole-house outage. Call day or night.
- Cheap parts firstBreaker, switch and tank get checked before the pump.
- Certified for the wellWork down the well goes to a state-certified pro.
- Price before pullingYou hear the cost before anything comes out of the well.
What's it doing?
Signs Your Well Pump Is Failing
Not every one of these means a new pump. Each points to a few likely causes, and one thing you can check first.
Pressure fades, then comes back
The pump is drawing water faster than the well refills, or the pump is wearing out.
Check firstRun one or two fixtures at a time. If it only happens with the hose or sprinklers going, it may be a low-yield well.
Clicks on and off constantly
Short cycling, usually from a waterlogged pressure tank, wrong tank air charge, or a bad check valve or switch.
Check firstTap the tank. A full, heavy thud all the way up means water has filled the space meant for air.
Runs and never shuts off
A leak between the well and the house, a worn pump that can't reach cut-off pressure, or a low water level.
Check firstClose the valve to the house. If the pump still won't shut off, the problem is at the well.
Air spitting from faucets
The water level dropping to the pump, a cracked drop pipe, or a failing check valve.
Check firstNote whether it's every faucet or just one. Every faucet means the well system.
Sandy or cloudy water
Sediment pulled in by a pump set too low, a damaged screen or an aging well casing.
Check firstCheck the whole-house filter. A fast-clogging filter tells the plumber a lot.
Well pump repair
Well Pump Repair in Valdosta, GA Starts Above Ground
A well system is four parts in a row. The three above ground fail more often, cost less, and get checked before anyone touches the pump.
Breaker & control box
Power for the pump. Submersible pumps often have a control box with a start capacitor.
Pressure switch
Turns the pump on at the cut-in pressure and off at cut-off. Its contacts pit and burn over time.
Pressure tank
Holds water under an air cushion so the pump isn't starting for every glass of water.
The pump
Down the well casing, or beside the house on a jet pump. Usually the last thing to suspect.
Pressure Tanks & Switches
Most short cycling, and plenty of “dead pump” calls, start here. These parts sit in the garage, a closet or the pump house, and they're ordinary plumbing work.
- Air charge
- With the tank drained, its air pressure should sit a couple of psi below the switch's cut-in setting.
- Waterlogged tank
- When the bladder fails, water fills the whole tank, the air cushion is gone, and the pump short cycles.
- Pressure switch
- Common settings are 30/50 or 40/60 psi. Burned contacts or a clogged sensing tube make it misbehave.
Submersible vs. Jet Pumps
The pump type decides how a repair goes. Switching from a jet pump to a submersible isn't always simple, since it can take a wider casing, new wire and new pipe.
Submersible
- Where
- Down in the well casing, pushing water up the drop pipe
- Suits
- Deeper wells; quiet; no priming
- Repair
- Pulled up with its pipe and wire to replace
Jet pump
- Where
- Above ground, beside the house or in a pump house, pulling water up
- Suits
- Shallow wells; easy to reach
- Repair
- Can lose prime; often rebuilt or swapped in place
A new pump
Well Pump Replacement
A pump replacement should start with proof the pump is the problem, and end with a tank set up to protect the new one.
Confirm the failure
Amp draw and wire tests at the control box, so the pump is proven bad before it comes up.
Pull and inspect
Pump, drop pipe, wire and check valve come up together and get looked over.
Size the new pump
Matched to the well depth, the water level and what the house uses, not just the old label.
Set and test
New pump down, wiring sealed, then pressure and flow checked at the tank.
Reset the tank
Tank air charge and switch settings matched so the new pump doesn't short cycle.
After the repair
Well Water Testing and Permits in Valdosta
A pump job opens the well. It's a good moment to think about what's coming out of it, and what the county requires for new wells.
Test once a year
The EPA recommends testing a private well every year for total coliform bacteria, nitrates, total dissolved solids and pH, and right away if the taste, color or smell changes. After a flood, don't drink from the well.
Under Valdosta
The City's own water comes from seven deep wells into the Upper Floridan aquifer, a limestone layer that starts about 200 feet below ground here. Private wells vary in depth, and depth decides the pump.
$60
County well permit
Lowndes County Environmental Health's fee for a well permit on its own. Filed with a septic permit, there's no extra charge, so a new well and a septic tank installation cost less to permit together.
Well pump costs
What Sets the Price of Well Pump Work
A new pressure switch and a new pump on a deep well sit at opposite ends. Three things decide where yours falls.
Part or pump
A pressure switch, capacitor or tank is above ground. Pulling a submersible pump from deep in a well is a different job.
Depth and what comes up
A deeper well means more pipe and wire to pull, and more of everything if those need replacing too.
When the water stops
No water on a Saturday night is an after-hours call, which costs more than a weekday visit.
Asked to replace a pump after one tripped breaker? It's fair to ask for the amp draw and wire test results first. A pump that ran nonstop can trip on heat and recover once it cools.
How plumbing jobs are pricedQuestions
Well Pump FAQ
Pump lifespan, what burns one out, the clicking that signals trouble, and how often a well should be tested.
Call (229) 544-0276What is the average cost of a well pump repair?
It depends on what failed. A pressure switch, capacitor or pressure tank is a smaller job than pulling and replacing a submersible pump, and well depth changes how much pipe and wire comes up. You'll hear the price before work starts.
What is the average lifespan of a well pump?
There's no set number. Pumps that start and stop constantly, run dry or pull sand wear out much sooner than ones on a healthy well with a properly charged tank. Keeping the tank and switch in shape is the best way to make a pump last.
What burns out a well pump?
Short cycling from a waterlogged tank, running dry when the water level drops, a leak that keeps it running nonstop, sand and sediment, and bad voltage or wiring. Each one adds heat and wear to the motor.
How do I tell if a well pump is worn out?
Pressure that fades sooner than it used to, a pump that runs long or won't shut off, higher power bills, and air or sand in the water. A plumber can measure amp draw to tell a worn pump from a bad switch or tank.
Why does my well pump keep clicking on and off?
That's short cycling, and the pressure tank is the usual cause, with a failed bladder or a low air charge. A leaking check valve or a faulty pressure switch can do it too. Left alone, it shortens the pump's life.
What should I do if my well has no water?
Check the pump's breaker and the gauge at the pressure tank. If the breaker keeps tripping, or the pump hums or runs without building pressure, switch the breaker off so it can't run dry, and call.
Who can replace a well pump in Georgia?
Georgia licenses water well drillers and certifies pump installers through the Water Well Standards Advisory Council, with EPD as its agent. Ask for the certificate or license number before anyone pulls a pump.
How often should I test my well water?
Every year for total coliform bacteria, nitrates, total dissolved solids and pH, according to the EPA, and right away if the taste, color or smell changes.
Keep reading
More Help for Well Homes
- Water line repair
Leaks in the line from the well to the house.
- Leak detection
A pump that runs with every faucet closed.
- Septic tank service
The other half of most well homes.
- Water softener installation
Hard water and iron from a private well.
- Water heater repair
Sediment from well water settling in the tank.
- 24/7 emergency plumbing
No water in the house, any hour.
No Water From the Well? Call Now
Pressure tanks, switches, submersible and jet pumps. Describe what the well is doing and hear the price first.